Gestalt Virouge, which we rebuilt for Kyoei USA out of Arizona. These went from a 2-piece to 3-piece modular design with larger lips, powdercoated silver faces, and high polished barrels including the portion where the tire covers!
Our customer Matt (tiltmode43 for you RX8clubbers) recently sent us some test fit shots of his new wheels.
We helped Matt source these Weds Kranze Bazreias and relipped them to 19x11.5 with an offset that utilizes as much inner clearance as possible down to the last millimeter. This allows him to run a 275/30/19 with room to spare.
This included new forged lips, pad shaving, and finishing them off with a mirror shine. He will soon have a full Fabulous aero kit so look out for that. The kit will be an excellent complement to these wheels.
One of our loyal customers recently decided to go all out on his CCW LM20's.
First, we took the wheels apart and polished the lips.
Then, the face registers were machined flat for a custom sandwich mount and then were plated in 24 karat gold along with the CCW centercaps and ARP hardware.
Because the wheels are now sandwich mounted, they are an additional 0.25" wider. The main benefit of this is that the entire lip is revealed.
Contact us today if you are interested in something similar.
We've been incredibly busy lately so there hasn't been much time to post up our work.
Formula Drift driver Ken Gushi recently brought over his Auto Couture Magnifique wheels off of his 3rd gen Lexus GS to get resized. His wheels received new lips which were 2 inches wider for a better fit.
Don't mind the missing bolt.
Ken was recently flown out to Japan for ONE day by Scion to test drive their new FR-S sports car. It is refreshing to see someone like him stick to his roots and still daily around in an old Hachiroku!
I'm a sucker for S2000's. Especially ones that don't look off-the-shelf. This one from the country down under appears to have a modified Amuse widebody kit. I'm not really feeling the rear, but I can definitely respect the work done to it. The front though, is a work of art. It works so well with the Spoon mirror covers. Your car can be wide and not have to look like a plastic transformer.
In this series, I'd like to share photos of beautiful wheel designs from Japan. Instead of bitching about replica wheels destroying our industry, I feel that the more optimistic approach of celebrating and spreading authentic wheels is more effective.
I can honestly say that we've worked on nearly every JDM wheel out there that people like to rock today. I have seen the areas that certain manufacturers cut corners. I have also gained a whole new respect for Volk monoblock wheels and I believe they are a step above the competition... but that's a blog post for another day.
Today, I'd like to share some propaganda for the K-Break Hybreed Fivesta. This wheel is a relatively late release (2010?) but utilizes a classic 5-spoke center mated to a euro step-lip. I personally think that step lips are more visually appealing than reverse lips.
K-Break has not paid for this post, though I would gladly accept payment in form of ground up Fivesta faces so I can sprinkle the shavings in my lunch. (Credit goes out to Yuta Akaishi for that suggestion - it really spices up your food!)
The Fivesta is a perfect blend of race aggressiveness and classy style. It even has immeasurably perfect spoke sharpness and face curvature. It is perfection.
The only downfall? With the miserable yen rate, you're going to pay around $4500-$5000 for a set. Start saving.
Recently, we were contacted by a good friend at VMR regarding a batch of erroneously produced 18x9.5 5x112 VMR V710 wheels. These wheels were made with a +50 offset which wouldn't really work for any cars in their Volkswagen, Audi, and Mercedes market.
Enter WheelFlip. With a strong S2000 background, I knew that these would be an excellent "aggressive-but-not-over-the-top" non-staggered setup for that car. That in mind, we went ahead and purchased them all with the intention of bringing VMR Wheels to the 5x114.3 market. We would utilize our own re-drill and insert service and convert the wheels upon purchase.
Even though we're in close proximity to VMR's warehouse, we are still one of few stocking dealers. Whether you're after our customized wheels or their Euro-drilled offerings, you should contact WheelFlip. Our pricing is lower than what we're allowed to publicly advertise!
This particular 2007 Honda S2000 is running the Gunmetal V710's with 265/35/18 Yokohama Advan Neova AD07 tires.
It's front fenders and quarter panels were professionally rolled.
So how much work exactly does it take to fit these wheels? Well, there are a few variables such as fender work, suspension drop, desired tire size, and camber settings.
Personally, I would suggest minor fender work all around, 255 width tires, and the "camber it 'til they fit" approach. You should easily be able to clear these with -2.5 camber in the front and -3.5 in the rear.
These VMR V710's will give your car an aggressive, but classy look at an affordable price! Pricing for this particular set (with re-drill) is $999! Custom finishes are available. Contact us today if you're interested.
First off, let me introduce this new sector of the blog that I have been meaning to write. I often make "the morning rounds" before beginning the day's work, and by that, I mean that I visit a few top blogs - some of which are listed to the side of this post. And on these blogs, I come across photos of many cars. And after viewing said photos, I form opinions, and that is what I will write about here.
I think of myself as a well-rounded car builder. I sometimes have odd tastes, but in general, I can see the big picture and appreciate anything as long as it is well done.
Leading off this new section; I'd like to get back to the topic's seemingly provoking title: The Perfect Stance.
Stance is a really broad subject and the perfect stance is subjective in more ways than most people can understand. Today though, I'm going to look at it from a judge's perspective. I have never judged a car show personally, however there are many times that I wish I could have that opportunity. As the winner of WekFest's first ever "Best Stance" award, I feel qualified enough to at least write this post, so hear me out.
Because "Stance" includes such a broad number of cars, it might just be the hardest category to judge at a car show. At least 75% of import show cars today have good stance, and that is a conservative estimate. Below, I have compiled a list of elements to consider.
Vehicle height and fender gap. If your car is low enough to eliminate the fender gap and the wheels are flush enough (within reason) to fill up the wheel well, then congratulations, you're officially one step closer to that award than a quarter of your peers.
With that out of the way, let's examine the basic definition of "good stance" in layman's terms: A car with good stance must simply look aggressive. Just remember, the car which displays this in the greatest way, wins. This also means that if you go overboard in one way or another, then your chances are slimmer. Now obviously "the bar" and our perceptions grow everyday. A few years ago, having -5 camber was almost unheard of in the US. Now, we literally have people with 4 times that amount driving their cars daily. It all comes down to how you present the entire package. Read on, and I'll explain.
Ugh, this is already going downhill. I am defying every fiber in my body telling me not to use cheesy terminology, but I will push on.
I'll go ahead and bring this one out early on. If your car is dropped on air suspension, you're not going to win in my book. No, air suspension is not "cheating" and it's actually really nice to have on a daily driver if your setup is decent. The problem with air suspension is that it never looks right. When you're at REAL drive height (and I'm not talking about creeping at 5mph), it's full blown retardation. Fender gap with unnecessary stretched tires, uneven higher-than-stock ride height in some cases, and unnecessary camber are just some of the side effects. Then when the cups or bags deflate, you get retarded amounts of toe-in on the rear suspension, and toe-out on the front suspension. Trust me, I have been there and done that. With 4 wheels pointing in 4 different directions, the car looks crippled. Often times, the front will slam lower than the rear, or vice versa and you're left with a front bumper that's on the ground and the rear pointing skyward (IE: MK5 VW Golf GTI).
Are you on coilovers with high spring rates? If so, excellent. Do you have liberal amounts of negative camber? If so, even better. Does the camber match from front to rear? This is very important as I find it to be attention to detail. A lot of cars these days (especially FWD macpherson setups, for some reason) tend to run upwards of -10 degrees of negative camber and then forget about the front. This is one setup that can make your car look broken and unbalanced. Front camber must be at least half of rear camber. On the contrary, if you have excessive negative camber in front with very little in the rear, this doesn't look all that bad. Lots of drift cars utilize this setup for maximum contact patch all around. This brings me onto the old phrase, "form follows function". This is true and applies in every sense. Does your car drive how it sits? With air suspension, the typical answer is that it does not. Also, if you spun your coilovers down at the show, then the case is the same. Do your wheels or tires rub on the fenders. A little rub is acceptable, but if it causes damage to your fenders and/or chunks up and shaves down the tires, then you have poor fitment, period. Consider that another round of disqualifications.
In short, how well are you framing the wheels? Since there are so many cars with great fitment at a typical show, it's necessary to be picky and eliminate all cars until you're left with one. After all, we're looking to award the car with The Best Stance. This means that it must embody that word in every way, shape, and form. If your fenders and quarter panels are not PRISTINE, then kiss your chances goodbye. That means a lot, right there. How can you have fenders in good condition while being flush at the same time? This of course means that custom bodywork must be done. Whether it's a small pull being smoothed out or a full on widebody, the fenders must be repainted. The fenders must also line up with the bumpers. If you flare the quarter panel, then you're fully expected to flare the rear bumper to match. Getting back to framing the wheels; are the fenders radiused? Are you running a proportionate wheel size compared to the size of your car? If you go wide, you must go up as well. By enlarging the quarter panel, you are effectively dwarfing the size of the wheels. The style of flare must be functional. Let me explain. If you use a fender roller and keep pulling outwards, it will eventually start pushing the fender up and you get a cute little flare that covers the tire, but limits vertical clearance. So even if you can roll straight without rubbing, the moment you hit a bump in the road, you're going to rub, and that my friends, is not functional.
And finally, having aftermarket aero is a great bonus. Part of stance is how mean the car looks head on, so headlights and front bumper definitely play a roll. That is one thing that a lot of people don't consider.
Simply put, how baller are your wheels? First off, if you're on replicas, you shouldn't even be showing. A 3-piece wheel shines here, literally and figuratively. Multipiece wheels give you a multitude of things to customize. You can having massive width, you can control lip sizing, lip style (stepped or reverse), lip finishing, face finishing, hardware finishing, and nail the offset perfectly without the aid of spacers. Wider wheels are better, and the tires should be stretched to a certain degree for clearance. Are the wheels rare/expensive? Is the finishing custom? Are your tires matching and of decent quality? "Stance" can be a quite expensive detail on a car so people often cheap out with ugly all-season tires. There is nothing wrong with that, it's just not as a good as it can be. I have been guilty of this. At the very least, the tires should be facing the right way, should be rolling the right way, and should have good tread remaining.
Everything is better in moderation
If a setup is already flush, why add spacers and more negative camber? Why do people camber it until their wheels are no longer flush? I have seen tires stretched so far that inner barrel is revealed on both sides. I am guilty of this, but it is not necessary unless one wanted extreme poke, in which case they wouldn't win anyways.
The Perfect Stance
So what constitutes the perfect stance? Before I answer that, I just want to say that if it were up to me, I would not have won that award at Wekfest.
The perfect stance must be awarded to a car that looks *good* even if it had poor stance. In other words, a Daewoo Nubira cannot win, no matter what. The car that I am picturing has a CLEAN custom metal widebody, similar to the one done on my S2000. The aggressive aftermarket bumpers will also be modified to line up. The car is on custom revalved coilovers with high spring rates and decent shock travel (other suspension mods must be in place to ensure this). The car has tubbed inner fenders and it does not rub fender under any driving circumstance, including full-lock turns. It is low to the point where the frame will hit reflectors on the freeway, but the suspension is stiff enough to keep the bumper from excessively scraping. Even being this low with oversized wheels, the car is not tucking rim, which takes away from the beauty and shape of a round wheel. Unlike my S2000, this car has it's fenders built around one specific set of wheels. From 5 feet away and further, it looks amazingly clean and flush. Upon closer inspection, you'll find that you can fit a finger or two between the fender and tire. This is because the wheel IS flush with the paper thin fender, but the tire stretch (which is subtle) gives it the necessary clearance to prevent any chance of rub. The car has a little bit more than -5 degrees of negative camber all around, but it never looks excessive. It is sporting high quality wheels with a big brake kit visble behind the face.
Happily, there is a car out there that just about fits the bill, and it is none other than this white Acura TL which debuted at this year's WekFest: SF show. It wasn't 100% complete at that show, however it is seen here at the rainy Autofashion VIP meet in San Diego. The owner drove it all the way down from San Jose.
We recently worked on these Work Meister S1 3pc. wheels. A few bends were repaired, the lips were chromed, and the faces were brushed with polished windows, and then coated with a transparent version of our custom Burning Black color.
Laying down a transparent powdercoat over a polished finish is essentially how you get a "candy" finish.
Thanks to my buddy Matt for the photos.
Hello everyone, this is Alex posting from the Shanghai airport in China. I have zero access to facebook as it's blocked in the country. My associate Mike will be responding to all contact e-mails. Feel free to call the office as well if you need something.
Last night, we did a soft launch, inviting you all to try out the the marketplace. Right now, it is released in the most stripped down version possible. Other functions such as the smart browsing and messaging system are currently disabled on public accounts. These features will be pushed live in the next few days once we get most of the bugs worked out.
If you have any feedback at all (or if you want to suggest missing manufacturers), then please send us a message through the contact form.